Here is what I would like to do with my TS-209:
1) Start with a working RAID 1 array
2) Remove one of the drives and store it offsite as a backup
3) Insert a new drive identical to the one I just removed
4) Have the NAS rebuild the RAID 1 array using the old installed drive as the source
If I could do this, it would make offsite backups so quick and easy; swap the drives out, start the rebuild, and store the removed drive offsite.
Is this possible?
Rebuild RAID 1 array without waiting for failure
-
- New here
- Posts: 8
- Joined: Sun Sep 30, 2007 7:06 am
-
- Starting out
- Posts: 40
- Joined: Mon Sep 10, 2007 5:39 pm
Re: Rebuild RAID 1 array without waiting for failure
This is a ideal case. Please put a dump data to "raid1", and do your experiment to confirm your idea.
But , raid 1 will mirror WHOLE disk even the place is no data,
therefore, time will be consume.
Please share your experiment result in this forum
But , raid 1 will mirror WHOLE disk even the place is no data,
therefore, time will be consume.
Please share your experiment result in this forum
steveluscher wrote:Here is what I would like to do with my TS-209:
1) Start with a working RAID 1 array
2) Remove one of the drives and store it offsite as a backup
3) Insert a new drive identical to the one I just removed
4) Have the NAS rebuild the RAID 1 array using the old installed drive as the source
If I could do this, it would make offsite backups so quick and easy; swap the drives out, start the rebuild, and store the removed drive offsite.
Is this possible?
-
- New here
- Posts: 8
- Joined: Sun Sep 30, 2007 7:06 am
-
- Starting out
- Posts: 40
- Joined: Mon Sep 10, 2007 5:39 pm
Oh, DON'T do the experiment, if you're already use the TS in raid1.
steveluscher wrote:Can you please clarify what you mean by "please put a dump data to 'raid 1'"? I don't understand.
I don't have the liberty to do experiments; the data on my RAID 1 array is live, valuable, and not backed up anywhere else.
- kent
- QNAP Staff
- Posts: 198
- Joined: Fri Aug 31, 2007 5:21 pm
- Location: Taipei, Taiwan
Re: Rebuild RAID 1 array without waiting for failure
The purpose of RAID 1 is not to backup your data. We don't suggest you do that.steveluscher wrote:Here is what I would like to do with my TS-209:
1) Start with a working RAID 1 array
2) Remove one of the drives and store it offsite as a backup
3) Insert a new drive identical to the one I just removed
4) Have the NAS rebuild the RAID 1 array using the old installed drive as the source
If I could do this, it would make offsite backups so quick and easy; swap the drives out, start the rebuild, and store the removed drive offsite.
Is this possible?
RAID 1 is to protect your data when one of your HDD become fail.
I am Kent. Nice to meet you!
-
- New here
- Posts: 8
- Joined: Sun Sep 30, 2007 7:06 am
Understood.
That out of the way – is there a way to make this work? I could imagine a situation whereby you might be able to simulate a failure on one drive, forcing a rebuild.
If one knew where to set the "this drive has failed" flag, perhaps you could trick the TS-209 into rebuilding the array onto a fresh hard disk.
Any thoughts?
That out of the way – is there a way to make this work? I could imagine a situation whereby you might be able to simulate a failure on one drive, forcing a rebuild.
If one knew where to set the "this drive has failed" flag, perhaps you could trick the TS-209 into rebuilding the array onto a fresh hard disk.
Any thoughts?
- kent
- QNAP Staff
- Posts: 198
- Joined: Fri Aug 31, 2007 5:21 pm
- Location: Taipei, Taiwan
If you would like to test the rebuilding function, follow below steps:steveluscher wrote:Understood.
That out of the way – is there a way to make this work? I could imagine a situation whereby you might be able to simulate a failure on one drive, forcing a rebuild.
If one knew where to set the "this drive has failed" flag, perhaps you could trick the TS-209 into rebuilding the array onto a fresh hard disk.
Any thoughts?
1. Make the volume as RAID 1
2. Hot-swap HDD 1 or HDD 2
3. After heard bee...the raid status is in degraded mode. You can check it via web management page.
4. hen plug-in the original HDD
5. After heard bee...the raid status is in rebuilding . You can check it via web management page.
However, I strongly recommand that the purpose of RAID 1 is not to backup your data.
Please carefully do the test, and always remember to backup your important data first!
I am Kent. Nice to meet you!