[Discussion] Not entering HDD standby mode?
-
- Been there, done that
- Posts: 700
- Joined: Mon Aug 27, 2007 1:16 pm
- Location: Taipei
- Contact:
[Discussion] Not entering HDD standby mode?
First of all, make sure you have enabled the "disk standby mode" function in System Tools/ Hardware Settings on the administration page. If the function does not work according to your settings, you may check if the following services are running. There must NOT be any access to these services for the HDD standby mode to work.
1. UPnP function on NAS, your router or IP sharing device
2. NTP server
3. BT download
4. AD service
5. QNAP Finder
6. Share folder mapping
7. DMZ service on your router or IP
Also, if your NAS is shared among multiple PC on the same network, be sure there is no access from the PC to the NAS.
Note: If you have installed add-on programs like SlimServer on your NAS, the HDD standby mode of QNAP NAS might not function since these programs might affect the service access status to the NAS.
1. UPnP function on NAS, your router or IP sharing device
2. NTP server
3. BT download
4. AD service
5. QNAP Finder
6. Share folder mapping
7. DMZ service on your router or IP
Also, if your NAS is shared among multiple PC on the same network, be sure there is no access from the PC to the NAS.
Note: If you have installed add-on programs like SlimServer on your NAS, the HDD standby mode of QNAP NAS might not function since these programs might affect the service access status to the NAS.
Last edited by QNAPRei on Wed Sep 05, 2007 11:18 am, edited 1 time in total.
-
- Starting out
- Posts: 29
- Joined: Mon Sep 03, 2007 7:04 pm
- Location: UK
Mine goes into standby when I'm watching a movie from it or when I am listening to music off it.
Its the only thing I can see that would cause it to stop responding after an hour ever hour since I have had it. I've changed it to see if it works, because to me it doesn't seem like a hdd spindown its more like a network reset on the box ://
Mines the TS-209 btw.
Its the only thing I can see that would cause it to stop responding after an hour ever hour since I have had it. I've changed it to see if it works, because to me it doesn't seem like a hdd spindown its more like a network reset on the box ://
Mines the TS-209 btw.
-
- Starting out
- Posts: 29
- Joined: Mon Sep 03, 2007 7:04 pm
- Location: UK
-
- Starting out
- Posts: 29
- Joined: Mon Sep 03, 2007 7:04 pm
- Location: UK
1. Model name - TS-209
2. Firmware version - Version 1.1.0 build 0727T
3. Operation System (OS) - Vista 32Bit
4. OS Language - English
5. Number of HDDs - 2
6. HDD model - Hitachi HDS721075KLA330 GK8O
7. HDD capacity - 750GB unformatted. 698.64GB formatted
8. RAID configuration - Raid0
9. Services enabled - Just microsoft networking, FTP, multimedia etc. off at the moment
10. External devices - None
11. Network bandwidth/ MTU - GigE 1000mb
2. Firmware version - Version 1.1.0 build 0727T
3. Operation System (OS) - Vista 32Bit
4. OS Language - English
5. Number of HDDs - 2
6. HDD model - Hitachi HDS721075KLA330 GK8O
7. HDD capacity - 750GB unformatted. 698.64GB formatted
8. RAID configuration - Raid0
9. Services enabled - Just microsoft networking, FTP, multimedia etc. off at the moment
10. External devices - None
11. Network bandwidth/ MTU - GigE 1000mb
-
- Starting out
- Posts: 20
- Joined: Tue Sep 04, 2007 2:14 am
- Location: Germany
- Contact:
HDD standby not work
Hi,
I'm using TS-209 with two Samsung HD501LJ (single drive mode).
The HDD standby not work. I have configured it to 10 minutes. Nobody access the TS-209 and the download station is not running.
I tried this with Firmware version 1.1.0 and updated then to Version 1.1.1 build 0831T. The problem still occures.
Any ideas ?
regards,
Ingo
I'm using TS-209 with two Samsung HD501LJ (single drive mode).
The HDD standby not work. I have configured it to 10 minutes. Nobody access the TS-209 and the download station is not running.
I tried this with Firmware version 1.1.0 and updated then to Version 1.1.1 build 0831T. The problem still occures.
Any ideas ?
regards,
Ingo
-
- Starting out
- Posts: 33
- Joined: Tue Sep 04, 2007 4:35 pm
Another won't-standby QNAP here
Model: TS-209
Firmware: 1.1.1 build 0831T
Disks: 2x WD5000AAKS
Config: RAID-1
Router: Draytek Vigor 2600
Services: FTP, web file, download, multmedia, twonky (rescan = 0)
Even tried unplugging the network cable and still no spin down.
Come on QNAP - this seems like a common problem and it's one of the most important features to me.
Hoping for help......
pingu.
Model: TS-209
Firmware: 1.1.1 build 0831T
Disks: 2x WD5000AAKS
Config: RAID-1
Router: Draytek Vigor 2600
Services: FTP, web file, download, multmedia, twonky (rescan = 0)
Even tried unplugging the network cable and still no spin down.
Come on QNAP - this seems like a common problem and it's one of the most important features to me.
Hoping for help......
pingu.
Last edited by pingu on Tue Sep 04, 2007 8:05 pm, edited 1 time in total.
-
- Starting out
- Posts: 49
- Joined: Mon Sep 03, 2007 5:50 pm
-
- Starting out
- Posts: 29
- Joined: Mon Sep 03, 2007 7:04 pm
- Location: UK
I don't know what's going on with mine then! As mine seems to go into standby for fun when it feels like it. I can be sitting here streaming a movie from it or listening to music and all of a sudden it will just stop playing at all. Then I have to wait about 2 minutes for the NAS to respond to me, then i have to restart the song or movie as it will only play upto the point before it freezes.
I've put the latest firmware on also now and that solves nothing.
It also doesn't matter what I have the standby settings put at. I can have it on 5 minutes or 5 hours or off and it still seems random :/
Whats the next step is solving this?
Dan
I've put the latest firmware on also now and that solves nothing.
It also doesn't matter what I have the standby settings put at. I can have it on 5 minutes or 5 hours or off and it still seems random :/
Whats the next step is solving this?
Dan
- nightyy
- Getting the hang of things
- Posts: 50
- Joined: Mon Sep 03, 2007 7:18 pm
I think everyone should provide additional dat alike:
router model (gateway of the NAS)
nas + firmware
running services
effects
Mine:
AVM Fritzbox 7170
TS-109 v1.1.1
only ftp+samba+downloadstation
-> spins down for around two thirds of the total time if notebook is on, spins down permanently if my notebook is off, never spins down if i use anything from the ts-109
router model (gateway of the NAS)
nas + firmware
running services
effects
Mine:
AVM Fritzbox 7170
TS-109 v1.1.1
only ftp+samba+downloadstation
-> spins down for around two thirds of the total time if notebook is on, spins down permanently if my notebook is off, never spins down if i use anything from the ts-109
------------------------
Qnap TS-109, 1.1.4, Western Digital Caviar GP WD10EACS 1 TB
http://nachtrab.de/category/qnap-nas/
Qnap TS-109, 1.1.4, Western Digital Caviar GP WD10EACS 1 TB
http://nachtrab.de/category/qnap-nas/
-
- Starting out
- Posts: 29
- Joined: Mon Sep 03, 2007 7:04 pm
- Location: UK
-
- Starting out
- Posts: 33
- Joined: Tue Sep 04, 2007 4:35 pm
Well, would you believe it, it has starting working for me.
Set it to 30 mins, shut down all PCs. Came back and it was in standby - the fan still spins but on low. (Note that the status LED didn't go out immediately - took a few seconds after it had spun down).
So, logged in to admin interface and heard the disks spin up. Changed the standby setting to 5 mins - shut down PC again and about 7 mins later, it entered standby mode again.
I will keep an eye on it to see if it is reliable.
Set it to 30 mins, shut down all PCs. Came back and it was in standby - the fan still spins but on low. (Note that the status LED didn't go out immediately - took a few seconds after it had spun down).
So, logged in to admin interface and heard the disks spin up. Changed the standby setting to 5 mins - shut down PC again and about 7 mins later, it entered standby mode again.
I will keep an eye on it to see if it is reliable.
- nightyy
- Getting the hang of things
- Posts: 50
- Joined: Mon Sep 03, 2007 7:18 pm
If the PCs are off it is reliable for me. However if the pcs are one, once in a while the nas starts to spin up. Wonder which windows service is contacting it regularly? Computer browser? network agent?
------------------------
Qnap TS-109, 1.1.4, Western Digital Caviar GP WD10EACS 1 TB
http://nachtrab.de/category/qnap-nas/
Qnap TS-109, 1.1.4, Western Digital Caviar GP WD10EACS 1 TB
http://nachtrab.de/category/qnap-nas/
- christian
- Moderator
- Posts: 754
- Joined: Tue Sep 04, 2007 5:27 pm
- Location: Germany
- Contact:
- nightyy
- Getting the hang of things
- Posts: 50
- Joined: Mon Sep 03, 2007 7:18 pm
@christian
have you tried disconnecting the nas from the network to see if it suspends the disks then?
have you tried disabling all of the services?
set suspend time to 5 minutes for testing purposes!
have you tried disconnecting the nas from the network to see if it suspends the disks then?
have you tried disabling all of the services?
set suspend time to 5 minutes for testing purposes!
------------------------
Qnap TS-109, 1.1.4, Western Digital Caviar GP WD10EACS 1 TB
http://nachtrab.de/category/qnap-nas/
Qnap TS-109, 1.1.4, Western Digital Caviar GP WD10EACS 1 TB
http://nachtrab.de/category/qnap-nas/
- nightyy
- Getting the hang of things
- Posts: 50
- Joined: Mon Sep 03, 2007 7:18 pm
In my setup the netbios service looked up the nas every now and then and it woke up then. I deactivated it and and now the NAS, though mounted as network drive, does not wake up if not accessed:
http://nachtrab.de/2007/09/04/qnap-ts-1 ... -sporadic/
http://nachtrab.de/2007/09/04/qnap-ts-1 ... -sporadic/
------------------------
Qnap TS-109, 1.1.4, Western Digital Caviar GP WD10EACS 1 TB
http://nachtrab.de/category/qnap-nas/
Qnap TS-109, 1.1.4, Western Digital Caviar GP WD10EACS 1 TB
http://nachtrab.de/category/qnap-nas/