Qget (http or ftp) download problem
-
- First post
- Posts: 1
- Joined: Mon Sep 24, 2007 5:02 pm
Qget (http or ftp) download problem
E.g. Download manual M_TS-209_20070727_V1.0.0_CHT.zip
Download by Qget size -5192kb(Can't open)
Download by browser size -5233kb(No problem)
TS-209Pro, Version 1.1.0 Build 0727T
Download by Qget size -5192kb(Can't open)
Download by browser size -5233kb(No problem)
TS-209Pro, Version 1.1.0 Build 0727T
-
- First post
- Posts: 1
- Joined: Tue Oct 09, 2007 12:46 am
I have raised a similar issue with Qnap support but not heard anything back since the 21st September. Below are two examples of the diagnostic information on the download. As you can see the Percentage is bigger than 100% and the download totals are larger than the size.
Dump Diagnostic Information:
Size: 350.5 MB
Percent: 100.1 %
Download Totals: 350.9 MB
Upload Total: ---
Share Time: ---
Start Time: Wed Sep 19 19:28:08 2007
No Error!
Size: 28.5 MB
Percent: 101.6 %
Download Totals: 29.0 MB
Upload Total: ---
Share Time: ---
Start Time: Fri Sep 21 13:00:57 2007
No Error!
Not tested with the beta 1.1.2 firmware.
T-209Pro Version 1.1.1 build 0831T
Dump Diagnostic Information:
Size: 350.5 MB
Percent: 100.1 %
Download Totals: 350.9 MB
Upload Total: ---
Share Time: ---
Start Time: Wed Sep 19 19:28:08 2007
No Error!
Size: 28.5 MB
Percent: 101.6 %
Download Totals: 29.0 MB
Upload Total: ---
Share Time: ---
Start Time: Fri Sep 21 13:00:57 2007
No Error!
Not tested with the beta 1.1.2 firmware.
T-209Pro Version 1.1.1 build 0831T
-
- Starting out
- Posts: 15
- Joined: Sun Oct 07, 2007 6:35 pm
I'd like to quote myself from this thread where I posted it a bit off-topic:
I too seem to have this problem (with the old firmware and the beta one). Some http downloads are broken some are not (it usually downloads a bit more than it should -> 102% finished). This also seems to be an issue when I log in via SSH and download the file with wget.
Any update would be appreciated.
Thanks
QNAP 109
-
- Starting out
- Posts: 15
- Joined: Sun Oct 07, 2007 6:35 pm
Followup to my previous post...
This still seems to be an issue even with the new firmware (although it wasn't mentioned in the release notes, it could have been fixed)...
3 of 4 files donwloaded just fine, one was messed up (it said 100.8 % in the error log). Why isn't this reproducible? So strange...
This still seems to be an issue even with the new firmware (although it wasn't mentioned in the release notes, it could have been fixed)...
3 of 4 files donwloaded just fine, one was messed up (it said 100.8 % in the error log). Why isn't this reproducible? So strange...
QNAP 109
-
- Experience counts
- Posts: 1786
- Joined: Sat Oct 13, 2007 2:21 am
- Location: Germany
i have exatly the same problem.
every HTTP or FTP download is corrupted. e.g.:
teh manual from the QNAP website:
M_TS-109_V1-1-0_DEU_2007-07-05.zip
1st try: 5.132KB
2nd try: 5.148KB
3rd try: 5.139KB
4th try: 5.118KB
5th try: 5.145KB
none of the files could be opened.
torrent files seem to work correctly.
what can we do to fix this?
every HTTP or FTP download is corrupted. e.g.:
teh manual from the QNAP website:
M_TS-109_V1-1-0_DEU_2007-07-05.zip
1st try: 5.132KB
2nd try: 5.148KB
3rd try: 5.139KB
4th try: 5.118KB
5th try: 5.145KB
none of the files could be opened.
torrent files seem to work correctly.
what can we do to fix this?
-
- Experience counts
- Posts: 1786
- Joined: Sat Oct 13, 2007 2:21 am
- Location: Germany
i tried to download the manual from qnap again.
according to ps, the download is called like this:
wget -T 30 -t 3 -c --no-cache -P /share/Qdownload/ --limit-rate=0 http://w3.ieiworld.com/QNAPFiles/downlo ... -07-05.zip
when i let it finish, the file is currupted. if i paste exactly this line into a ssh session then the file is downloaded correctly.
so why is wget working correctly from a ssh shell but not from DownloadStation or QGet?
i would say this is a serious bug! it makes the DownloadStation completely useless.
according to ps, the download is called like this:
wget -T 30 -t 3 -c --no-cache -P /share/Qdownload/ --limit-rate=0 http://w3.ieiworld.com/QNAPFiles/downlo ... -07-05.zip
when i let it finish, the file is currupted. if i paste exactly this line into a ssh session then the file is downloaded correctly.
so why is wget working correctly from a ssh shell but not from DownloadStation or QGet?
i would say this is a serious bug! it makes the DownloadStation completely useless.
TVS-1282 | Version 4.4.3 | 3x 12TB WDC WD121KRYZ RAID5
TS-639 Pro | Version 4.2.6 | 5x 3TB WDC WD30EFRX RAID5 as Backup
LianLi EX-50 with 3x 2TB SAMSUNG HD203WI + 2x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
LianLi EX-503 with 5x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
TS-639 Pro | Version 4.2.6 | 5x 3TB WDC WD30EFRX RAID5 as Backup
LianLi EX-50 with 3x 2TB SAMSUNG HD203WI + 2x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
LianLi EX-503 with 5x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
-
- Experience counts
- Posts: 1786
- Joined: Sat Oct 13, 2007 2:21 am
- Location: Germany
ok i found out that the downloadStation just doesn't finish the download. it simply kills wget before it is done.
i found this out by letting qget download the manual again, and of cours it was currupt. then i entered the wget command from my last post in a ssh shell and wget picked up on that download and finished it. now the file could be opened.
so it seens that the download station is moving files to the done-list before they are actualy done.
come on qnap there has got to be a way to fix this, please!!!
i found this out by letting qget download the manual again, and of cours it was currupt. then i entered the wget command from my last post in a ssh shell and wget picked up on that download and finished it. now the file could be opened.
so it seens that the download station is moving files to the done-list before they are actualy done.
come on qnap there has got to be a way to fix this, please!!!
TVS-1282 | Version 4.4.3 | 3x 12TB WDC WD121KRYZ RAID5
TS-639 Pro | Version 4.2.6 | 5x 3TB WDC WD30EFRX RAID5 as Backup
LianLi EX-50 with 3x 2TB SAMSUNG HD203WI + 2x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
LianLi EX-503 with 5x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
TS-639 Pro | Version 4.2.6 | 5x 3TB WDC WD30EFRX RAID5 as Backup
LianLi EX-50 with 3x 2TB SAMSUNG HD203WI + 2x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
LianLi EX-503 with 5x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
- QNAPIvan
- Experience counts
- Posts: 1020
- Joined: Mon Jul 02, 2007 4:03 pm
Dear all:
Sorry for inconvenience.
We are looking at this issue and will solve it ASAP.
Cheers,
Sorry for inconvenience.
We are looking at this issue and will solve it ASAP.
Cheers,
________________________________________
Product Marketing Director
USA Online Support: http://www.qnap.com/i/useng/before_buy/ ... wone&cid=2
Support email: q_supportus@qnap.com
USA Technical Support: +1 909 595 2782
Product Marketing Director
USA Online Support: http://www.qnap.com/i/useng/before_buy/ ... wone&cid=2
Support email: q_supportus@qnap.com
USA Technical Support: +1 909 595 2782
-
- Experience counts
- Posts: 1786
- Joined: Sat Oct 13, 2007 2:21 am
- Location: Germany
ok i found a little workaround. (which doesn't seem to work everytime)
when downloading a file with qget you just have to let it finish. then remove it from the finish list and keep the file. then you have to download the same file again, this will resume the first download and finish it. it will show more than 100% but once the second download is finished (takes just a couple seconds) the file is alright.
thanks QNAPIvan. could you please inform us when this issue is solved.
when downloading a file with qget you just have to let it finish. then remove it from the finish list and keep the file. then you have to download the same file again, this will resume the first download and finish it. it will show more than 100% but once the second download is finished (takes just a couple seconds) the file is alright.
thanks QNAPIvan. could you please inform us when this issue is solved.
TVS-1282 | Version 4.4.3 | 3x 12TB WDC WD121KRYZ RAID5
TS-639 Pro | Version 4.2.6 | 5x 3TB WDC WD30EFRX RAID5 as Backup
LianLi EX-50 with 3x 2TB SAMSUNG HD203WI + 2x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
LianLi EX-503 with 5x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
TS-639 Pro | Version 4.2.6 | 5x 3TB WDC WD30EFRX RAID5 as Backup
LianLi EX-50 with 3x 2TB SAMSUNG HD203WI + 2x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
LianLi EX-503 with 5x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
- QNAPIvan
- Experience counts
- Posts: 1020
- Joined: Mon Jul 02, 2007 4:03 pm
Dear niwa2
No problem, will updtae to this thread once the solution is available.
Thanks for all of your effort and sorry for late reply for this issue.
Cheers,
No problem, will updtae to this thread once the solution is available.
Thanks for all of your effort and sorry for late reply for this issue.
Cheers,
________________________________________
Product Marketing Director
USA Online Support: http://www.qnap.com/i/useng/before_buy/ ... wone&cid=2
Support email: q_supportus@qnap.com
USA Technical Support: +1 909 595 2782
Product Marketing Director
USA Online Support: http://www.qnap.com/i/useng/before_buy/ ... wone&cid=2
Support email: q_supportus@qnap.com
USA Technical Support: +1 909 595 2782
-
- New here
- Posts: 4
- Joined: Mon Oct 22, 2007 10:55 pm
- Location: Germany
Same here. Nearly every download (http/ftp) is corrupt.
Hope you can fix this quickly...
Marphy
P.S.: Just start some records at onlinetvrecorder.com and try to download them via mirror and TS-109. All will work fine, but after encoding, the Media Player refuses playing.
Hope you can fix this quickly...
Marphy
P.S.: Just start some records at onlinetvrecorder.com and try to download them via mirror and TS-109. All will work fine, but after encoding, the Media Player refuses playing.
QNAP TS-109 1.1.3 1029T
Samsung SpinPoint T166 HD500LJ 500GB
Personally recognized bugs:Current satisfaction: annoyed.
Samsung SpinPoint T166 HD500LJ 500GB
Personally recognized bugs:Current satisfaction: annoyed.
-
- Experience counts
- Posts: 1786
- Joined: Sat Oct 13, 2007 2:21 am
- Location: Germany
hi
i tried firmware 1.1.3 beta. the download of small files is working now, but lage files are still not finished. i tried a 340MB file and about 2MB were missing. again, starting the same download with wget via SSH finished it correcty.
another strange thing appeares now. when downloading a file the percentage jumps to 99.0% when it reaches a value greater than 99.0% and stays there for a while. suddenly 100% appears and the download is done.
from what i can see so far the percentage of the download is somehow calculated or determined wrong (the percentage shown is higher than the actual). it seems that 99% are recognized and a wait time has been added to finish the download. but if the filesize is too big or the download too slow then it is still finished too early (it seems like wget is killed before it is done). so far this fix is not satisfying. the determination of the right percentage should be the way to go, not adding some waittimes. why not checking if wget is still running, cause that would mean that the download is not done yet, or at least DO NOT KILL WGET, it will shut down itselve once it is done.
now i am waiting for you next attempt of fixing this.
let me know if i can help
i tried firmware 1.1.3 beta. the download of small files is working now, but lage files are still not finished. i tried a 340MB file and about 2MB were missing. again, starting the same download with wget via SSH finished it correcty.
another strange thing appeares now. when downloading a file the percentage jumps to 99.0% when it reaches a value greater than 99.0% and stays there for a while. suddenly 100% appears and the download is done.
from what i can see so far the percentage of the download is somehow calculated or determined wrong (the percentage shown is higher than the actual). it seems that 99% are recognized and a wait time has been added to finish the download. but if the filesize is too big or the download too slow then it is still finished too early (it seems like wget is killed before it is done). so far this fix is not satisfying. the determination of the right percentage should be the way to go, not adding some waittimes. why not checking if wget is still running, cause that would mean that the download is not done yet, or at least DO NOT KILL WGET, it will shut down itselve once it is done.
now i am waiting for you next attempt of fixing this.
let me know if i can help
TVS-1282 | Version 4.4.3 | 3x 12TB WDC WD121KRYZ RAID5
TS-639 Pro | Version 4.2.6 | 5x 3TB WDC WD30EFRX RAID5 as Backup
LianLi EX-50 with 3x 2TB SAMSUNG HD203WI + 2x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
LianLi EX-503 with 5x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
TS-639 Pro | Version 4.2.6 | 5x 3TB WDC WD30EFRX RAID5 as Backup
LianLi EX-50 with 3x 2TB SAMSUNG HD203WI + 2x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
LianLi EX-503 with 5x 2TB SAMSUNG HD204UI in RAID5 as Backup drive
-
- New here
- Posts: 4
- Joined: Mon Oct 22, 2007 10:55 pm
- Location: Germany
I do not understand why a so wide-spreaded but simple problem needs that a long time to be solved... Althrogh QNAP seems to be very commited to have pleased customers, bug-fixing lasts too long I think.
Regards,
Marphy
Regards,
Marphy
QNAP TS-109 1.1.3 1029T
Samsung SpinPoint T166 HD500LJ 500GB
Personally recognized bugs:Current satisfaction: annoyed.
Samsung SpinPoint T166 HD500LJ 500GB
Personally recognized bugs:Current satisfaction: annoyed.