Resetting to factory defaults
-
- Starting out
- Posts: 11
- Joined: Thu Sep 06, 2007 10:25 pm
Resetting to factory defaults
How do you reset everything in a TS 209pro to the factory defaults. I've tried the reset button but it retained some information and now I am having a hard time getting the drives to reformat and show up correctly. I've updated with firmware 1.1.1 and want to roll back everything to just like it was out of the box
Any suggestions?
thanks
Any suggestions?
thanks
- kent
- QNAP Staff
- Posts: 198
- Joined: Fri Aug 31, 2007 5:21 pm
- Location: Taipei, Taiwan
The reset button only doing:
1. reset password of admin user to "admin"
2. reset network setting to DHCP
If you want to reset to factory default, just go to "System tools"->"Backup/Restore/Reset settings" in administration page.
Then click reset button to reset to factory default.
1. reset password of admin user to "admin"
2. reset network setting to DHCP
If you want to reset to factory default, just go to "System tools"->"Backup/Restore/Reset settings" in administration page.
Then click reset button to reset to factory default.
I am Kent. Nice to meet you!
-
- Starting out
- Posts: 11
- Joined: Thu Sep 06, 2007 10:25 pm
Thank you Kent,
I did that and all of the default folders are now gone, (Qmultimedia, Qweb, Public etc.)
And after running the quick setup again, whenever I go into the User Management section I get a message that says
Warning
Your disk volume is being formatted or checked. Please wait for the completion of formatting or checking, or go to the SATA Disk page to initialize the disk.
I've let the TS-209 sit all night (9 Hours) and I'm still getting the same message.
Also when I look at the log files I'm getting this message every 30 seconds:
Warning Re-launch process [proftpd].
Did I do something wrong? All I'm trying to do is convert the linear disk set up that I had the 209 at before the disk failure to a RAID 1 with 2 disks.
I did that and all of the default folders are now gone, (Qmultimedia, Qweb, Public etc.)
And after running the quick setup again, whenever I go into the User Management section I get a message that says
Warning
Your disk volume is being formatted or checked. Please wait for the completion of formatting or checking, or go to the SATA Disk page to initialize the disk.
I've let the TS-209 sit all night (9 Hours) and I'm still getting the same message.
Also when I look at the log files I'm getting this message every 30 seconds:
Warning Re-launch process [proftpd].
Did I do something wrong? All I'm trying to do is convert the linear disk set up that I had the 209 at before the disk failure to a RAID 1 with 2 disks.
- kent
- QNAP Staff
- Posts: 198
- Joined: Fri Aug 31, 2007 5:21 pm
- Location: Taipei, Taiwan
Please read announcements first.
I would like to know
1. What is your disk configuration?
2. What is your server name?
I would like to know
1. What is your disk configuration?
2. What is your server name?
I am Kent. Nice to meet you!
-
- Starting out
- Posts: 33
- Joined: Thu Sep 06, 2007 6:05 am
jeerkahn what did you do to resolve it? i have the same problem.
Warning
Your disk volume is being formatted or checked. Please wait for the completion of formatting or checking, or go to the SATA Disk page to initialize the disk.
but nothing happens. this error came out of the blue and the logfile says nothing.
Ivan
Warning
Your disk volume is being formatted or checked. Please wait for the completion of formatting or checking, or go to the SATA Disk page to initialize the disk.
but nothing happens. this error came out of the blue and the logfile says nothing.
Ivan
Qnap TS 209
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
-
- Starting out
- Posts: 17
- Joined: Wed Sep 05, 2007 12:25 am
-
- Starting out
- Posts: 33
- Joined: Thu Sep 06, 2007 6:05 am
yeps
yeps was doing nothing (except connecting via afp but then i got an error that i could not connect. so there it began for me. no i see light activity on the disks but once in a few minutes so its not doing something. i could try a restart from the webmenu.
i guess the data is already lost already
only that exclamation mark is the second time already (first time it was only the public folder (i lost all data also back then).
it should take away worries about securing my data but it aint so far.
maybe its better to return to firmware 1.1.0
ivan
i guess the data is already lost already
only that exclamation mark is the second time already (first time it was only the public folder (i lost all data also back then).
it should take away worries about securing my data but it aint so far.
maybe its better to return to firmware 1.1.0
ivan
Qnap TS 209
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
-
- Starting out
- Posts: 33
- Joined: Thu Sep 06, 2007 6:05 am
restarted
hm i restarted and it looked at first everything was oke in the user and share management tool but after 10 seconds it got me the:
Warning
Your disk volume is being formatted or checked. Please wait for the completion of formatting or checking, or go to the SATA Disk page to initialize the disk.
again. so it took me to nowhere
iwill let it run till tomorrowmorning (its 2.30 am here now). i hope its fixes itself, what i doubt.
Warning
Your disk volume is being formatted or checked. Please wait for the completion of formatting or checking, or go to the SATA Disk page to initialize the disk.
again. so it took me to nowhere
iwill let it run till tomorrowmorning (its 2.30 am here now). i hope its fixes itself, what i doubt.
Qnap TS 209
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
-
- Starting out
- Posts: 26
- Joined: Thu Sep 06, 2007 9:25 pm
Have you resolved this issue because I am about to try the same thing and I don't want to get stuck with a dead box.
Marc
Marc
NAS: TS-209
Firmware: Version 1.1.1 build 0831T
Raid: Off
HDD: 1 x 500Gb Seagate (ST3500630AS 3.AA) & 1 x 300Gb Maxtor (6V300F0)
SlimServer Installed
USB Drive: 1 x 500Gb NTFS
OS: Windows Vista
Firmware: Version 1.1.1 build 0831T
Raid: Off
HDD: 1 x 500Gb Seagate (ST3500630AS 3.AA) & 1 x 300Gb Maxtor (6V300F0)
SlimServer Installed
USB Drive: 1 x 500Gb NTFS
OS: Windows Vista
-
- Starting out
- Posts: 33
- Joined: Thu Sep 06, 2007 6:05 am
hai marct
he marct,
pm the hoster of the site because the solved the problem with ssh access to my disk, the did something which was the solution for me.
ivan
pm the hoster of the site because the solved the problem with ssh access to my disk, the did something which was the solution for me.
ivan
Qnap TS 209
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
- qn00b
- Know my way around
- Posts: 228
- Joined: Thu Oct 11, 2007 12:54 am
- Location: Ontario, Canada
After playing around and experimenting, I eventually pulled the drives, attached them to my XP system via a USB harness and removed all the partitions.
When re-installed, the TS209 Pro approached them as brand new drives, so setup launched as if I pulled the NAS out of the box for the first time.
It would be nice if they would post a Telnet or Winscp method of killing the partitions and forcing a restart, etc.
When re-installed, the TS209 Pro approached them as brand new drives, so setup launched as if I pulled the NAS out of the box for the first time.
It would be nice if they would post a Telnet or Winscp method of killing the partitions and forcing a restart, etc.
-
- Starting out
- Posts: 33
- Joined: Thu Sep 06, 2007 6:05 am
okay
okay thx for your reply. I keep notice of it when it happens again. It should not may happen (because it is my only backup (on two mirrored drives). I hope it doesnt happen again but i should not be worrying about it
Ivan
Ivan
Qnap TS 209
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap
Macosx 10.4.10 and macosx 10.5 (9A527)
Firmware 1.1.1 (0831)
2x700gb Seagate ST3750640AS 3.AA
Mirroring Disk Volume
servername: qnap